Executive Adhesive & Fastener Kit w/AT-8040 Adhesive
This Kit Contains A Large Selection Of All The Common Weld Mount Parts And Is An Ideal Kit For The Full Service Yard Or Custom Builder. The Kit Contains 1 Tube Of Our AT-8040 No Slide Multi Bonder Acrylic Adhesive Which Will Bond To Almost All Surfaces Except Low Energy Plastic Or Rubber. AT-8040 Will Hold Even Our Heaviest Parts on a Vertical or Overhead Surface Without Fixturing. The Adhesive Sets in 12 Minutes And Is Heat Resistant To 225°. The Adhesive Should Be Refrigerated and Has A Shelf Life Of 1 year.
The Weld Mount System Eliminates The Need To Drill Into Cored Composites Which Can Result In Hull & Deck Delaminations. No Need To Drill, Tap, or Weld When Used On Metal Surfaces. Great For Mounting Electronics, Wire Runs, Bilge Applications, Water Separators, Battery Switches, Etc.
The AT-1001003 Kit Contains:
- (1) AT-8040 – No Slide Multi Bonder Acrylic Adhesive
- <(1) AT-300 - Dispensing Gun
- (10) AT-850 – 3.5″ Mixing Tips For AT-8040 Adhesive
- (100) AT-5 – Large White Cable Tie Mount
- (50) AT-3 – Small White Cable Tie Mount
- (4) AT-113 – Large Footman’s Strap
- (10) PS62-832-16SS – 1.00″ Long Panel Stud
- (4) ST125-1420-16SS – 1.00″ Long Stud With 1/4 x 20 Threads 1.25″ Base
- (4) ST125-1420-24SS – 1.50″ Long Stud With 1/4 x 20 Threads 1.25″ Base
- (4) ST125-1024-12SS – .75″ Long Stud With #10 x 24 Threads 1.25″ Base
- (4) ST125-1024-24SS – 1.50″ Long Stud With #10 x 24 Threads 1.25″ Base
- (1) Plano Storage Box 14″ x 9″ x 2.75″
- Step By Step Instructions
| Weight | 6.5 g |
|---|---|
| Dimensions | 15 × 9 × 3 cm |
Brand
Weld Mount
No accessories available for this product.
Videos
Video 1: Link
Related products
Boat Outfitting > Tools
White Nylon Wire Tie Mount The AT-5 tie mount is designed to be set into wet resin during the hull lay up or bonded with our acrylic adhesives. It’s designed for a #5 wire tie and has an average pull strength of 150 lbs. It’s approved for submerged bilge applications. Stop putting plywood in your [...]
Boat Outfitting > Tools
White Nylon Wire Tie Mount The AT-3 tie mount is smaller for panel and other small space applications. This part is molded in white nylon and is sized for a #3 wire tie with a maximum width of .20″. Average pull strength is about 50 lbs. The square base measures .44″ wide. Use this smaller [...]
Boat Outfitting > Tools
Footman’s Strap Mount The Footman’s Strap Mount is designed to be bonded with AT-4020 Acrylic Adhesive. This strap mount is 3.25″ long and 1″ wide and holds up to a 1.3″ max strap width. This strap is incredibly strong, paintable, and is rated for over 600 lbs. strength. Use it for battery and tank tie [...]
Boat Outfitting > Tools
Black Nylon Wire Tie Mount The AT-3 tie mount is smaller for panel and other small space applications. This part is molded in black nylon and is sized for a #3 wire tie with a maximum width of .20″. Average pull strength is about 50 lbs. The square base measures .44″ wide. Use this smaller [...]
Boat Outfitting > Tools
Weld Mount 1″ Tall Stainless Panel Stud w/0.62″ Base & #8 x 32 Thread – Qty. 15
1″ Tall Stainless Stud w/#8 x 32 Thread Our Small Stainless Steel Panel Studs have a wide range of uses. Originally they were used for mounting on the backside of dash panels for mounting to the console. Now they are used for securing a wide range of wire clamps and other small components to composite [...]
Boat Outfitting > Tools
Weld Mount 1.5″ Tall Stainless Stud w/1/4″ x 20 Threads – Qty. 10
1.5″ Tall Stainless Stud w/1/4″ x 20 Thread Mounts to virtually any surface using the AT-4010 Acrylic Adhesive. This is a structural part with 500 lbs. of tensile strength and 650 lbs. in shear. All studs have 1/4″ x 20 threads. Use for hanging panels, through deck mounts and many other uses.
Boat Outfitting > Tools
Floating Nut Plates Our floating nut plate is designed for through-hole mounting applications. The rubber fixture holds the part in the through hole while it is bonded in place with our acrylic adhesive. The fixture keeps the threads clean during bonding. Remove the rubber fixture when you are ready to make up the assembly. The [...]
Boat Outfitting > Tools
Weld Mount 2″ Tall Stainless Stud w/3/8″ x 16 Threads – Qty. 5
2″ Tall Stainless Stud w/3/8″ x 16 Thread The HS200 stud is designed for heavy load applications such as mounting filters and panels. Thestud is inertial (friction) welded to a 2″ base plate creating a very strong part. Manufactured of 304 stainless steel. Tensile strength is approximately 1,200 lbs. and shear strength is 1,500 lbs.