-
×
BoatLIFE Life-Calk Cartridge - Black
1 × $29.99
Black Nylon Wire Tie Mount
The AT-3 tie mount is smaller for panel and other small space applications. This part is molded in black nylon and is sized for a #3 wire tie with a maximum width of .20″. Average pull strength is about 50 lbs. The square base measures .44″ wide. Use this smaller wire tie for runs with only a few wires or where space prevents use of our larger tie mounts. Excellent for mounting compass wires on center console boats and for overhead panel runs.
Related products
Boat Outfitting > Tools
$39.99
Black Nylon Wire Tie Mount The AT-5 tie mount is designed to be set into wet resin during the hull lay up or bonded with our acrylic adhesives. It’s designed for a #5 wire tie and has an average pull strength of 150 lbs. It’s approved for submerged bilge applications. Stop putting plywood in your [...]
Boat Outfitting > Tools
$32.60
Black Nylon Wire Tie Mount The AT-3 tie mount is smaller for panel and other small space applications. This part is molded in black nylon and is sized for a #3 wire tie with a maximum width of .20″. Average pull strength is about 50 lbs. The square base measures .44″ wide. Use this smaller [...]
Out of stock
Boat Outfitting > Tools
Weld Mount Manual Dual Pusher Rod f/AT-2010 & AT-4020 – Qty. 10
$23.64
Dual Pusher Rod The AT-500 dual pusher rod is used to dispense equal amounts of our AT-2010 or AT-4020 adhesive for manual mixing. This dual pusher rod can not be used with our AT-300 or AT-350 mixing tips as it does not generate enough force to push the adhesives through the tip.
Out of stock
Boat Outfitting > Tools
Weld Mount 2.5″ Tall Stainless Stud w/1/4″ x 20 Threads – Qty.10
$56.99
2.5″ Tall Stainless Stud w/1/4″ x 20 Thread Mounts to virtually any surface using the AT-4010 Acrylic Adhesive. This is a structural part with 500 lbs. of tensile strength and 650 lbs. in shear. All studs have 1/4″ x 20 threads. Use for hanging panels, through deck mounts and many other uses.
Out of stock
Boat Outfitting > Tools
Weld Mount 2″ Tall Stainless Stud w/3/8″ x 16 Threads – Qty. 5
$69.99
2″ Tall Stainless Stud w/3/8″ x 16 Thread The HS200 stud is designed for heavy load applications such as mounting filters and panels. Thestud is inertial (friction) welded to a 2″ base plate creating a very strong part. Manufactured of 304 stainless steel. Tensile strength is approximately 1,200 lbs. and shear strength is 1,500 lbs.
Boat Outfitting > Tools
$52.51
White Nylon Wire Tie Mount The AT-3 tie mount is smaller for panel and other small space applications. This part is molded in white nylon and is sized for a #3 wire tie with a maximum width of .20″. Average pull strength is about 50 lbs. The square base measures .44″ wide. Use this smaller [...]
Out of stock
Boat Outfitting > Tools
Weld Mount 1.5″ Tall Stainless Panel Stud w/0.62″ Base & #8 x 32 Threads – Qty. 15
$31.99
1.5″ Tall Stainless Stud w/#8 x 32 Thread Our Small Stainless Steel Panel Studs have a wide range of uses. Originally they were used for mounting on the backside of dash panels for mounting to the console. Now they are used for securing a wide range of wire clamps and other small components to composite [...]
Out of stock
Boat Outfitting > Tools
$299.99
Aluminum Base Wire Tie Mount This tie mount is provided with an anodized aluminum base with a nylon tie mount which is riveted to the base. The nylon mount swivels 360 degrees making alignment with the wire harness easier. This tie mount is designed for a #5 wire tie and has an average pull strength [...]