Zinc Anode Kit
The Actuators on each Seakeeper Ride controller have sacrificial anodes that need to be periodically inspected and replaced when about half of the anode has worn down.
Installation
- Remove the blade by unscrewing the four (4) M8-1.25 x 20mm screws and their washers.
- Unscrew the two (2) M4-0.7 x 12 mm bolts holding the zinc sacrificial anode.
- Attach the new zinc sacrificial anode using the two (2) M4-0.7 x 12mm bolts and tighten to 20 in-lbs (2.3 N-m).
- Reattach the Blade using the four (4) M8-1.25 x 20mm screws and their washers. Be sure to use thread-locking sealant with an activator/primer when reinstalling hardware. Torque these four (4) bolts to 80 in-lbs (9.0 N-m) in an “X” pattern.
This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.
| Weight | 0.8 g |
|---|---|
| Dimensions | 3 × 3 × 3 cm |
Brand
Seakeeper Ride
No accessories available for this product.
No literature available for this product.
No videos available for this product.
Related products
Boat Outfitting > Trim Tab Accessories
Actuator Lower Hinge WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or [...]
Boat Outfitting > Trim Tab Accessories
Actuator Assembly – 13.75″ Closed Length Actuator assembly is complete hydraulic cylinder. Piston-like strong arm that pushes tab into position. Sophisticated plastic resin body. Nylon upper hinge. Bends 5° in actual use. Fluid flows through concealed hole in upper hinge thus eliminating external hoses subject to damage. Hearty and flexible enough to demands of offshore [...]
Boat Outfitting > Trim Tab Accessories
Bennett actuators are strong but flexible nylon/fiberglass hydraulic cylinders. The piston-like arms push tabs into position. Fluid flows through a concealed hole in the upper hinge at the top of the actuator – thus eliminating external hoses subject to damage. A1200S is designed for installations where space is limited. WARNING: This product can expose you [...]
Boat Outfitting > Trim Tab Accessories
Hydraulic Power Unit A compact powerhouse that creates hydraulic pressure to lower and raise the trim tabs. It employs two solenoid valves to direct the flow of fluid to the actuators. The solenoid valves lock tightly to secure the tabs in place. Strength to lower and hold even the largest tabs in place. Lexan cover [...]
Boat Outfitting > Trim Tab Accessories
Lenco 101XD Extreme Duty Actuator – 12V – 2 1/4″ Stroke – 3/8″ Hardware
101 XD Actuator- 12 Volt- 2-1/4 Stroke with Mounting Hardware The 101 XD Actuator is used mostly with HD, XD, High Performance and Super Strong tabs. 2.25 stroke. Overall length (tip to tip) is 113/8 inches. Instant response electric actuators are made of high impact glass fiber filled, ultraviolet-resistant nylon material with 316 super [...]
Boat Outfitting > Trim Tab Accessories
Insta-Trim Boat Leveler 12 Volt Solenoid Valve with Green Wire. They are custom designed for Insta-Trim Boat Leveler Co., epoxy sealed and humidity resistant, thereby preventing shorting out. The solenoids lock the tabs in any position, eliminating driftback. Barb type hose fittings provide tight, secure connections.
Boat Outfitting > Trim Tab Accessories
Biodegradable Oil & Funnel Kit Biodegradable oil should be used only after motor pump is mounted to boat in vertical position, remove plug and add. Funnel also included.
Boat Outfitting > Trim Tab Accessories
Hydraulic Power Unit A compact powerhouse that creates hydraulic pressure to lower and raise the trim tabs. It employs two solenoid valves to direct the flow of fluid to the actuators. The solenoid valves lock tightly to secure the tabs in place. Strength to lower and hold even the largest tabs in place. Lexan cover [...]