BEP Easy Fit Battery Switch - 275A Continuous 
BEP Contour Battery Disconnect Switch - 275A Continuous 
Motor Flush Ear Muff
Outboard motor flushers quickly flush away salt, sand, minerals and contaminates from your lower unit cooling system extending the engine’s service life. Easy to use molded PVC cups deliver fresh water to flush the cooling system through side intakes on the lower unit. Simple garden hose connection, no tools required. Great for winterizing, tune-ups and other maintenance that requires running an outboard engine out of the water.
WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
| Weight | 0.7 g |
|---|---|
| Dimensions | 12 × 5 × 3 cm |
Brand
Sea-Dog
No accessories available for this product.
No literature available for this product.
No videos available for this product.
Related products
Boat Outfitting > Tools
Aluminum Wire Tie Used with Stainless Steel or Nylon wire ties up to 0.4 inches wide. 250 lbs tensile strength when bonded with AT-6030 adhesive manufactured of 5052 marine grade aluminum for UV and salt water resistance. Ideal alternative to welding or drilling and tapping to mount hoses, conduit, etc.
Boat Outfitting > Tools
Weld Mount AT-5B Large Black Nylon Wire Tie Mount – Qty. 100
Black Nylon Wire Tie Mount The AT-5 tie mount is designed to be set into wet resin during the hull lay up or bonded with our acrylic adhesives. It’s designed for a #5 wire tie and has an average pull strength of 150 lbs. It’s approved for submerged bilge applications. Stop putting plywood in your [...]
Boat Outfitting > Tools
Weld Mount 1.5″ Tall Stainless Panel Stud w/0.62″ Base & #8 x 32 Threads – Qty. 15
1.5″ Tall Stainless Stud w/#8 x 32 Thread Our Small Stainless Steel Panel Studs have a wide range of uses. Originally they were used for mounting on the backside of dash panels for mounting to the console. Now they are used for securing a wide range of wire clamps and other small components to composite [...]
Boat Outfitting > Tools
Weld Mount Stainless Nut Plate w/1/4″ x 20 Threads – Qty. 10
Floating Nut Plates Our floating nut plate is designed for through-hole mounting applications. The rubber fixture holds the part in the through hole while it is bonded in place with our acrylic adhesive. The fixture keeps the threads clean during bonding. Remove the rubber fixture when you are ready to make up the assembly. The [...]
Boat Outfitting > Tools
Weld Mount 1.5″ Tall Stainless Stud w/1/4″ x 20 Threads – Qty. 10
1.5″ Tall Stainless Stud w/1/4″ x 20 Thread Mounts to virtually any surface using the AT-4010 Acrylic Adhesive. This is a structural part with 500 lbs. of tensile strength and 650 lbs. in shear. All studs have 1/4″ x 20 threads. Use for hanging panels, through deck mounts and many other uses.
Boat Outfitting > Tools
Weld Mount 1″ Tall Stainless Stud w/1/4″ x 20 Threads – Qty. 10
1″ Tall Stainless Stud w/1/4″ x 20 Thread Mounts to virtually any surface using the AT-4010 Acrylic Adhesive. This is a structural part with 500 lbs. of tensile strength and 650 lbs. in shear. All studs have 1/4″ x 20 threads. Use for hanging panels, through deck mounts and many other uses.
Boat Outfitting > Tools
Weld Mount .75″ Tall Stainless Panel Stud w/0.62″ Base & #8 x 32 Thread – Qty. 15
.75″ Tall Stainless Stud w/#8 x 32 Thread Our Small Stainless Steel Panel Studs have a wide range of uses. Originally they were used for mounting on the backside of dash panels for mounting to the console. Now they are used for securing a wide range of wire clamps and other small components to composite [...]
Boat Outfitting > Tools
White Nylon Wire Tie Mount The AT-5 tie mount is designed to be set into wet resin during the hull lay up or bonded with our acrylic adhesives. It’s designed for a #5 wire tie and has an average pull strength of 150 lbs. It’s approved for submerged bilge applications. Stop putting plywood in your [...]