Emergency Deck Fill Plug
Nitrile-Buna Rubber
This Emergency Deck Fill Plug is a must for any vessel. Fits most 1-1/2″ hose deck fills in the event you lose your cap. For temporary use only until you can replace your OEM cap. Constructed of fuel resistant Nitrile-Buna rubber.
WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
| Weight | 0.3 g |
|---|---|
| Dimensions | 7 × 5 × 3 cm |
Brand
Sea-Dog
No accessories available for this product.
No literature available for this product.
No videos available for this product.
Related products
Boat Outfitting > Tools
White Nylon Wire Tie Mount The AT-5 tie mount is designed to be set into wet resin during the hull lay up or bonded with our acrylic adhesives. It’s designed for a #5 wire tie and has an average pull strength of 150 lbs. It’s approved for submerged bilge applications. Stop putting plywood in your [...]
Boat Outfitting > Tools
White Nylon Wire Tie Mount The AT-5 tie mount is designed to be set into wet resin during the hull lay up or bonded with our acrylic adhesives. It’s designed for a #5 wire tie and has an average pull strength of 150 lbs. It’s approved for submerged bilge applications. Stop putting plywood in your [...]
Boat Outfitting > Tools
Weld Mount Manual Dual Pusher Rod f/AT-2010 & AT-4020 – Qty. 10
Dual Pusher Rod The AT-500 dual pusher rod is used to dispense equal amounts of our AT-2010 or AT-4020 adhesive for manual mixing. This dual pusher rod can not be used with our AT-300 or AT-350 mixing tips as it does not generate enough force to push the adhesives through the tip.
Boat Outfitting > Tools
Footman’s Strap Mount The Footman’s Strap Mount is designed to be bonded with AT-4020 Acrylic Adhesive. This strap mount is 3.25″ long and 1″ wide and holds up to a 1.3″ max strap width. This strap is incredibly strong, paintable, and is rated for over 600 lbs. strength. Use it for battery and tank tie [...]
Boat Outfitting > Tools
Aluminum Base Wire Tie Mount This tie mount is provided with an anodized aluminum base with a nylon tie mount which is riveted to the base. The nylon mount swivels 360 degrees making alignment with the wire harness easier. This tie mount is designed for a #5 wire tie and has an average pull strength [...]
Boat Outfitting > Tools
Weld Mount 1.5″ Tall Stainless Stud w/1/4″ x 20 Threads – Qty. 10
1.5″ Tall Stainless Stud w/1/4″ x 20 Thread Mounts to virtually any surface using the AT-4010 Acrylic Adhesive. This is a structural part with 500 lbs. of tensile strength and 650 lbs. in shear. All studs have 1/4″ x 20 threads. Use for hanging panels, through deck mounts and many other uses.
Boat Outfitting > Tools
Weld Mount 1″ Tall Stainless Stud w/1/4″ x 20 Threads – Qty. 10
1″ Tall Stainless Stud w/1/4″ x 20 Thread Mounts to virtually any surface using the AT-4010 Acrylic Adhesive. This is a structural part with 500 lbs. of tensile strength and 650 lbs. in shear. All studs have 1/4″ x 20 threads. Use for hanging panels, through deck mounts and many other uses.
Boat Outfitting > Tools
Weld Mount AT-3B Small Black Nylon Wire Tie Mount – Qty. 100
Black Nylon Wire Tie Mount The AT-3 tie mount is smaller for panel and other small space applications. This part is molded in black nylon and is sized for a #3 wire tie with a maximum width of .20″. Average pull strength is about 50 lbs. The square base measures .44″ wide. Use this smaller [...]