Ancor 12-10 Gauge - #8 Heat Shrink Spade Terminals - 100 Pack 
Ronstan Tell Tails - Set of 3 Pairs 
Sufix Performance Lead Core - 15lb - 10-Color Metered - 600 yds 
Weld Mount AT-5 Large White Nylon Wire Tie Mount - Qty. 50 
Add-A-Snap – White – 4″
For use with canvas or nylon boat covers, the Add-A-Snap allows you to easily add length on hard to reach snaps from shrunken material. Nickel plated brass/nylon.
WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
| Weight | 0.05 g |
|---|---|
| Dimensions | 5 × 3 × 1 cm |
Brand
Sea-Dog
No accessories available for this product.
No literature available for this product.
No videos available for this product.
Related products
Boat Outfitting > Tools
Floating Nut Plates Our floating nut plate is designed for through-hole mounting applications. The rubber fixture holds the part in the through hole while it is bonded in place with our acrylic adhesive. The fixture keeps the threads clean during bonding. Remove the rubber fixture when you are ready to make up the assembly. The [...]
Boat Outfitting > Tools
Black Nylon Wire Tie Mount The AT-5 tie mount is designed to be set into wet resin during the hull lay up or bonded with our acrylic adhesives. It’s designed for a #5 wire tie and has an average pull strength of 150 lbs. It’s approved for submerged bilge applications. Stop putting plywood in your [...]
Boat Outfitting > Tools
White Nylon Wire Tie Mount The AT-5 tie mount is designed to be set into wet resin during the hull lay up or bonded with our acrylic adhesives. It’s designed for a #5 wire tie and has an average pull strength of 150 lbs. It’s approved for submerged bilge applications. Stop putting plywood in your [...]
Boat Outfitting > Tools
White Nylon Wire Tie Mount The AT-3 tie mount is smaller for panel and other small space applications. This part is molded in white nylon and is sized for a #3 wire tie with a maximum width of .20″. Average pull strength is about 50 lbs. The square base measures .44″ wide. Use this smaller [...]
Boat Outfitting > Tools
Weld Mount AT-5B Large Black Nylon Wire Tie Mount – Qty. 100
Black Nylon Wire Tie Mount The AT-5 tie mount is designed to be set into wet resin during the hull lay up or bonded with our acrylic adhesives. It’s designed for a #5 wire tie and has an average pull strength of 150 lbs. It’s approved for submerged bilge applications. Stop putting plywood in your [...]
Boat Outfitting > Tools
Weld Mount Single Poly Clamp f/1/4″ x 20 Studs – 1/4″ OD – Requires 0.75″ Stud – Qty. 25
Single Clamp Each clamp is designed to be mounted using 1/4″ x 20 Weld Mount studs. The clamps are manufactured in black polypropylene and are temperature rated for -22 to +194 degrees F continuous service. Features: Hose OD: 0.250″ Stud Required: ST125-1420-12SS Clamp Dimensions L/W/D: 0.87″ x 0.47″ x 0.41″ Recommended Clamp Spacing: 3′
Boat Outfitting > Tools
Footman’s Strap Mount The Footman’s Strap Mount is designed to be bonded with AT-4020 Acrylic Adhesive. This strap mount is 3.25″ long and 1″ wide and holds up to a 1.3″ max strap width. This strap is incredibly strong, paintable, and is rated for over 600 lbs. strength. Use it for battery and tank tie [...]
Boat Outfitting > Tools
Black Nylon Wire Tie Mount The AT-3 tie mount is smaller for panel and other small space applications. This part is molded in black nylon and is sized for a #3 wire tie with a maximum width of .20″. Average pull strength is about 50 lbs. The square base measures .44″ wide. Use this smaller [...]