Raymarine SeaTalkng Starter Kit
SeaTalkng is a robust cabling and connection system compatible with NMEA 2000, built specifically for the marine environment comprising a powered single backbone with two terminators, one at each end.
The SeaTalk to SeaTalkng Starter Kit is the perfect way to get started with your SeaTalkng compatible Raymarine product.
The 5-way connector forms the start of your SeaTalkng backbone and your SeaTalkng product is connected via a Spur Cable.
What’s in the kit?
A06064: SeaTalkng 5-way Connector
A06031: SeaTalkng Backbone Terminator (x2)
A06040: SeaTalkng Spur Cable 3M
A06049: SeaTalkng Power Cable
| Weight | 0.7 g |
|---|---|
| Dimensions | 10 × 9 × 7 cm |
Brand
Raymarine
No accessories available for this product.
No literature available for this product.
No videos available for this product.
Related products
Marine Navigation & Instruments > NMEA Cables & Sensors
Micro Inline Termination Resistor The inline terminator is used where the NMEA 2000® network is terminated at a product, for example the top of the mast at a weather instrument or GPS antenna/receiver. The inline terminator plugs directly into the product with the other end connected to the network cable Micro Termination resistors usually terminate [...]
Marine Navigation & Instruments > NMEA Cables & Sensors
The SeaTalkng Backbone kit contains everything you need to construct and wire a basic SeaTalkng navigation network backbone on board your vessel. The kit contains the following components: A06031 SeaTalkng Terminators (Qty. 2) A06037 Backbone Cable, 20m A06036 Backbone Cable, 5m (Qty. 2) A06028 T-Piece (Qty. 4) A06049 Network Power Cable 81300 SeaTalkng Reference Manual [...]
Marine Navigation & Instruments > NMEA Cables & Sensors
USB100 NMEA 2000® / USB Gateway Maretron’s USB100 is a gateway for bridging USB equipment using NMEA 0183 sentences – such as an on-board computer running navigational software – with an NMEA 2000® network. The gateway automatically converts incoming NMEA 2000® messages to NMEA 0183 sentences so you can continue benefiting from navigational and charting [...]
Marine Navigation & Instruments > NMEA Cables & Sensors
Micro Bulkhead Feed-Thru The Bulkhead Feed-Thru allows ease of installation through panels or bulkheads and establishes future connection points in a network installation. The bulkhead feed-thru also maintains the integrity of watertight bulkheads by providing a waterproof seal and connection Features rugged keyways for positive alignment of connections Waterproof rated to IP67
Marine Navigation & Instruments > NMEA Cables & Sensors
Micro Cap – Used to Cover Male Connector Micro cap used to cover male connectors.
Marine Navigation & Instruments > NMEA Cables & Sensors
TLA100 NMEA 2000®Tank Level Adapter The TLA100 is used to adapt commercially available resistive tank senders to the NMEA 2000® network. This allows you to observe tank levels anywhere on the vessel where there is an NMEA 2000® compatible display such as the Maretron DSM200. The TLA100 is compatible with both the American standard (240-33 [...]
Marine Navigation & Instruments > NMEA Cables & Sensors
J2K100 NMEA 2000® / J1939 Bridge (Engine/Transmission/Genset Gateway) Maretron’s J2K100 attaches directly into J1939 networks of compatible engines, transmissions, and gensets and converts the J1939 engine data to the NMEA 2000® marine digital interface. Critical engine, transmission, and genset data is then distributed throughout the vessel over a single cable where it can be monitored [...]
Marine Navigation & Instruments > NMEA Cables & Sensors
T-Connector For use with red NMEA network