SmartPlug 30 AMP Inlet & Female Cord Connector Combo - Stainless Steel 
N2KEXT NMEA2000 Cable Micro-C Medium Duty – 20M
20M (65.6 ft) Low loss 18-gauge cable recommended for network backbone runs resulting in a more robust network. Cables are identified by orange locking collars.
| Weight | 5.1 g |
|---|---|
| Dimensions | 10 × 10 × 3 cm |
Brand
Navico
No accessories available for this product.
No literature available for this product.
No videos available for this product.
Related products
Marine Navigation & Instruments > NMEA Cables & Sensors
NMEA Cable, 1 x 6 Pin Connector, 5 Meters WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
Marine Navigation & Instruments > NMEA Cables & Sensors
USB100 NMEA 2000® / USB Gateway Maretron’s USB100 is a gateway for bridging USB equipment using NMEA 0183 sentences – such as an on-board computer running navigational software – with an NMEA 2000® network. The gateway automatically converts incoming NMEA 2000® messages to NMEA 0183 sentences so you can continue benefiting from navigational and charting [...]
Marine Navigation & Instruments > NMEA Cables & Sensors
N2KEXT-2RD 2′ NMEA 2000 Cable 2′ NMEA 2000 Cable
Marine Navigation & Instruments > NMEA Cables & Sensors
RAA100 NMEA 2000®Rudder Angle Adapter The RAA100 is used to adapt commercially available resistive rudder angle senders to the NMEA 2000® network. This allows you to observe rudder angle anywhere on the vessel where there is an NMEA 2000® compatible display such as the Maretron DSM200. The RAA100 is compatible with both the American standard [...]
Marine Navigation & Instruments > NMEA Cables & Sensors
Micro Termination Resistors Termination Resistors are required on a NMEA 2000® network and are placed at each end of a network trunk cable. Like the double-ended cordsets, the termination resistors are waterproof and continue to function even while submerged in the bilge. Screw terminal connector for positive connections Termination resistors are used to terminate both [...]
Marine Navigation & Instruments > NMEA Cables & Sensors
PC-27BL Power Cable. For use with LCX-112C, LCX-113C HD, LCX-27C, LCX-28C HD, LCX-37C, LCX-38C HD, LMS-520C, LMS-522C Igps, LMS-525C DF, LMS-527C DF Igps, X510C, X515C DF. Works with: GlobalMap 5200C, GlobalMap 5300C iGPS, GlobalMap 7200C, GlobalMap 7300C HD, GlobalMap 8200C, GlobalMap 8300C HD, GlobalMap 9200C, GlobalMap 9300C HD, LCX-112C, LCX-113C HD, LCX-27C, LCX-28C HD, LCX-37C, [...]
Marine Navigation & Instruments > NMEA Cables & Sensors
Micro Inline Termination Resistor The inline terminator is used where the NMEA 2000® network is terminated at a product, for example the top of the mast at a weather instrument or GPS antenna/receiver. The inline terminator plugs directly into the product with the other end connected to the network cable Micro Termination resistors usually terminate [...]
Marine Navigation & Instruments > NMEA Cables & Sensors
J2K100 NMEA 2000® / J1939 Bridge (Engine/Transmission/Genset Gateway) Maretron’s J2K100 attaches directly into J1939 networks of compatible engines, transmissions, and gensets and converts the J1939 engine data to the NMEA 2000® marine digital interface. Critical engine, transmission, and genset data is then distributed throughout the vessel over a single cable where it can be monitored [...]