Fluid Level Sensor
Transmits the tank level from a suitable tank level sender unit on the the NMEA 2000 network.
Replaces EP-65 Reports Tank Fluid Level: 0-100% Pre-configured for Fuel Tank Instance 0 Pre-calibrated to the 33-240j U.S. marine standard tank level sender Can re-calibrated via compatible Navico MFDs to other standard levels Can be reconfigured* to output the following level types: Water, Gray Water, Live Well, Oil, Black Water.
Cable Length 10 feet and comes with a Micro-C T-Connector.
| Weight | 0.5 g |
|---|---|
| Dimensions | 10 × 4 × 2 cm |
Brand
Navico
No accessories available for this product.
No literature available for this product.
No videos available for this product.
Related products
Marine Navigation & Instruments > NMEA Cables & Sensors
The SeaTalkng Backbone kit contains everything you need to construct and wire a basic SeaTalkng navigation network backbone on board your vessel. The kit contains the following components: A06031 SeaTalkng Terminators (Qty. 2) A06037 Backbone Cable, 20m A06036 Backbone Cable, 5m (Qty. 2) A06028 T-Piece (Qty. 4) A06049 Network Power Cable 81300 SeaTalkng Reference Manual [...]
Marine Navigation & Instruments > NMEA Cables & Sensors
J2K100 NMEA 2000® / J1939 Bridge (Engine/Transmission/Genset Gateway) Maretron’s J2K100 attaches directly into J1939 networks of compatible engines, transmissions, and gensets and converts the J1939 engine data to the NMEA 2000® marine digital interface. Critical engine, transmission, and genset data is then distributed throughout the vessel over a single cable where it can be monitored [...]
Marine Navigation & Instruments > NMEA Cables & Sensors
Micro Termination Resistors Termination Resistors are required on a NMEA 2000® network and are placed at each end of a network trunk cable. Like the double-ended cordsets, the termination resistors are waterproof and continue to function even while submerged in the bilge. Screw terminal connector for positive connections Termination resistors are used to terminate both [...]
Marine Navigation & Instruments > NMEA Cables & Sensors
N2KEXT-15RD 15′ NMEA 2000 Cable 15′ NMEA 2000 Cable
Marine Navigation & Instruments > NMEA Cables & Sensors
Micro Termination Resistors Termination Resistors are required on a NMEA 2000® network and are placed at each end of a network trunk cable. Like the double-ended cordsets, the termination resistors are waterproof and continue to function even while submerged in the bilge. Screw terminal connector for positive connections Termination resistors are used to terminate both [...]
Marine Navigation & Instruments > NMEA Cables & Sensors
Micro Inline Termination Resistor The inline terminator is used where the NMEA 2000® network is terminated at a product, for example the top of the mast at a weather instrument or GPS antenna/receiver. The inline terminator plugs directly into the product with the other end connected to the network cable Micro Termination resistors usually terminate [...]
Marine Navigation & Instruments > NMEA Cables & Sensors
TLA100 NMEA 2000®Tank Level Adapter The TLA100 is used to adapt commercially available resistive tank senders to the NMEA 2000® network. This allows you to observe tank levels anywhere on the vessel where there is an NMEA 2000® compatible display such as the Maretron DSM200. The TLA100 is compatible with both the American standard (240-33 [...]
Marine Navigation & Instruments > NMEA Cables & Sensors
Furunos NX300 paperless Navtex receiver is the most economical way of monitoring navigational warnings, meteorological warnings, search and rescue information and other data for ships sailing within 200-400 n.m. of shore. Every incoming message is identified and new messages are read from the high-contrast 4.5″ LCD display, no paper is required. However, you can print [...]