Fuel Flow Sensor 8-10 LPM/2.1-18.5 GPM
When fluid passes through the sensor, the rotors turn. Magnets which are located in the rotors will pass across sensors in the sensor circuit board. Pulses from these sensors are transmitted to the FFM100 which performs flow rate calculations based on the received pulses.
Specifications:
- Construction: Housing Material Aluminum
- Port Size: 3/4″ NPT Female
- Maximum Viscosity: 1000 cPs
- Strainer Size: 60 Mesh (If not already installed after fuel filter)
WARNING: This product can expose you to chemicals including NICKEL (METALLIC) which is known to the State of California to cause cancer. For more information go to P65Warnings.ca.gov.
Brand
Maretron
No accessories available for this product.
Literature
Installation Guide: Download PDF
No videos available for this product.
Related products
Marine Navigation & Instruments > NMEA Cables & Sensors
Micro Cap – Used to Cover Male Connector Micro cap used to cover male connectors.
Marine Navigation & Instruments > NMEA Cables & Sensors
Micro Double-Ended Cordset – 3M Mechanical Contact Carrier Mat/Color: Thermoplastic PUR/Blue-Gray Molded Body Mat/Color: Thermoplastic PUR/Blue-Gray Contact Mat/Plating: Brass/Gold Coupling Nut Mat/Plating: Brass/Nickel Connector Outside Diameter: 0.59″ Electrical Current Rating: 4.0 Amps Voltage Rating: 250 VCable Outer Jacket Mat/Color: PVC/Gray Conductor Insulation Material: HDPE (data pair), SRPVC (power pair) Number of Conductors: 4X22 AWG, 22 [...]
Marine Navigation & Instruments > NMEA Cables & Sensors
Micro Termination Resistors Termination Resistors are required on a NMEA 2000® network and are placed at each end of a network trunk cable. Like the double-ended cordsets, the termination resistors are waterproof and continue to function even while submerged in the bilge. Screw terminal connector for positive connections Termination resistors are used to terminate both [...]
Marine Navigation & Instruments > NMEA Cables & Sensors
The SeaTalkng Backbone kit contains everything you need to construct and wire a basic SeaTalkng navigation network backbone on board your vessel. The kit contains the following components: A06031 SeaTalkng Terminators (Qty. 2) A06037 Backbone Cable, 20m A06036 Backbone Cable, 5m (Qty. 2) A06028 T-Piece (Qty. 4) A06049 Network Power Cable 81300 SeaTalkng Reference Manual [...]
Marine Navigation & Instruments > NMEA Cables & Sensors
TLA100 NMEA 2000®Tank Level Adapter The TLA100 is used to adapt commercially available resistive tank senders to the NMEA 2000® network. This allows you to observe tank levels anywhere on the vessel where there is an NMEA 2000® compatible display such as the Maretron DSM200. The TLA100 is compatible with both the American standard (240-33 [...]
Marine Navigation & Instruments > NMEA Cables & Sensors
Micro Inline Termination Resistor The inline terminator is used where the NMEA 2000® network is terminated at a product, for example the top of the mast at a weather instrument or GPS antenna/receiver. The inline terminator plugs directly into the product with the other end connected to the network cable Micro Termination resistors usually terminate [...]
Marine Navigation & Instruments > NMEA Cables & Sensors
PC-27BL Power Cable. For use with LCX-112C, LCX-113C HD, LCX-27C, LCX-28C HD, LCX-37C, LCX-38C HD, LMS-520C, LMS-522C Igps, LMS-525C DF, LMS-527C DF Igps, X510C, X515C DF. Works with: GlobalMap 5200C, GlobalMap 5300C iGPS, GlobalMap 7200C, GlobalMap 7300C HD, GlobalMap 8200C, GlobalMap 8300C HD, GlobalMap 9200C, GlobalMap 9300C HD, LCX-112C, LCX-113C HD, LCX-27C, LCX-28C HD, LCX-37C, [...]
Marine Navigation & Instruments > NMEA Cables & Sensors
USB100 NMEA 2000® / USB Gateway Maretron’s USB100 is a gateway for bridging USB equipment using NMEA 0183 sentences – such as an on-board computer running navigational software – with an NMEA 2000® network. The gateway automatically converts incoming NMEA 2000® messages to NMEA 0183 sentences so you can continue benefiting from navigational and charting [...]