NMEA 2000 Starter Kit – Dual Unit
From boat performance to weather and water conditions, make sense of it all with NMEA 2000 networking on your Humminbird control head. The NMEA 2000 Starter Kit – Dual provides the essential components to build a dual device NMEA 2000 network.
Features:
- Compatible with: HELIX G4N models and all SOLIX models
- Compatible Humminbird Legacy models (must also use (1) AS ETH NMEA2K and (1) AS EC QDE) : HELIX 7 G2N/G3N, all HELIX 8, all HELIX 9, all HELIX 10, all HELIX 12
- Kit includes: (1) 1 meter power cable and T-connector, (1) male terminator, (1) female terminator, (1) T-connector, (2) 2 meter (6.5ft) drop cables
- 1-Year Limited Warranty
| Weight | 2.3 g |
|---|---|
| Dimensions | 10 × 8 × 4 cm |
Brand
Humminbird
No accessories available for this product.
No literature available for this product.
No videos available for this product.
Related products
Marine Navigation & Instruments > NMEA Cables & Sensors
N2KEXT-15RD 15′ NMEA 2000 Cable 15′ NMEA 2000 Cable
Marine Navigation & Instruments > NMEA Cables & Sensors
Fluxgate Cable 10 Meters, 6 Pin Pigtail WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
Marine Navigation & Instruments > NMEA Cables & Sensors
Micro Termination Resistors Termination Resistors are required on a NMEA 2000® network and are placed at each end of a network trunk cable. Like the double-ended cordsets, the termination resistors are waterproof and continue to function even while submerged in the bilge. Screw terminal connector for positive connections Termination resistors are used to terminate both [...]
Marine Navigation & Instruments > NMEA Cables & Sensors
RAA100 NMEA 2000®Rudder Angle Adapter The RAA100 is used to adapt commercially available resistive rudder angle senders to the NMEA 2000® network. This allows you to observe rudder angle anywhere on the vessel where there is an NMEA 2000® compatible display such as the Maretron DSM200. The RAA100 is compatible with both the American standard [...]
Marine Navigation & Instruments > NMEA Cables & Sensors
J2K100 NMEA 2000® / J1939 Bridge (Engine/Transmission/Genset Gateway) Maretron’s J2K100 attaches directly into J1939 networks of compatible engines, transmissions, and gensets and converts the J1939 engine data to the NMEA 2000® marine digital interface. Critical engine, transmission, and genset data is then distributed throughout the vessel over a single cable where it can be monitored [...]
Marine Navigation & Instruments > NMEA Cables & Sensors
Micro Termination Resistors Termination Resistors are required on a NMEA 2000® network and are placed at each end of a network trunk cable. Like the double-ended cordsets, the termination resistors are waterproof and continue to function even while submerged in the bilge. Screw terminal connector for positive connections Termination resistors are used to terminate both [...]
Marine Navigation & Instruments > NMEA Cables & Sensors
Micro Bulkhead Feed-Thru The Bulkhead Feed-Thru allows ease of installation through panels or bulkheads and establishes future connection points in a network installation. The bulkhead feed-thru also maintains the integrity of watertight bulkheads by providing a waterproof seal and connection Features rugged keyways for positive alignment of connections Waterproof rated to IP67
Marine Navigation & Instruments > NMEA Cables & Sensors
Active Coupler with 15 Meter Interconnect Cable. Range: 80kHz to 30mHz WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. This product may not be returned to the original point of purchase. Please [...]