Perko LED Side Light - Green - 12V - White Plastic Housing 
0183 to N2K Gateway with PC Interface, ISO
The NGX-1 is an intelligent gateway that converts NMEA 0183 data to NMEA 2000 (and vice versa), allowing you to share information between devices from the two standards. This creates the possibility of upgrading some of the vessel’s electronics to NMEA 2000 and keeping the remaining NMEA 0183 devices. This can help spread the cost of transitioning to NMEA 2000, reducing the initial upgrade cost to accommodate a new NMEA 2000 device.
The ISO variant connects easily to NMEA 0183 devices with a dedicated pair of data wires for transmit and receive, allowing the NGX-1 to share data bi-directionally if required. OPTOIsolation is included on the input and groundbreaking ISO-DriveTM technology is on the output to keep your devices safe from hazardous ground loops.
The USB Variant allows for quick and easy connectivity to a PC running software that requires NMEA 0183 data.
Thanks to the device being low power, it is powered directly from the NMEA 2000 network, removing the requirement for an independent power supply.
The Actisense NGX-1 also makes it possible to send and receive NMEA 2000 data safely between a PC and an NMEA 2000 network. This creates the possibility of feature-rich software applications replacing or complementing dedicated hardware such as a Multifunction Display (MFD) or Chart Plotter.
Acting as an NMEA 2000 to PC Gateway allows the device to act as a rule-enforcing firewall between the PC and the network, giving the user full control over what data is passed and blocked. The NGX is capable of transferring every currently available NMEA 2000 PGN from the network to a PC application.
Features:
- ISO version has OPTO-isolated input and ISO-Drive output for safely interfacing with NMEA 0183 or RS232 / RS422.
- Advanced configuration using the Actisense Toolkit allows Tx / Rx lists and Tx rates to be set.
- Supports fast-heading at 10Hz.
- Up to 230,400 baud rate data transfer rate.
- Integrated 0.75m ISO cable.
- Diagnostic LEDs on both input and output.
Integrate Seamlessly with Raymarine® Products
The STNG-A06045 adaptor cable enables users to integrate Raymarine SeaTalkNG products into the standard configured NMEA 2000® bus and vice-versa. Currently only available when purchased with an Actisense NMEA 2000® Gateway product.
This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.
| Weight | 0.35 g |
|---|---|
| Dimensions | 6 × 6 × 2 cm |
Brand
Actisense
No accessories available for this product.
Literature
Brochure: Download PDF
No videos available for this product.
Related products
Marine Navigation & Instruments > NMEA Cables & Sensors
Furunos NX300 paperless Navtex receiver is the most economical way of monitoring navigational warnings, meteorological warnings, search and rescue information and other data for ships sailing within 200-400 n.m. of shore. Every incoming message is identified and new messages are read from the high-contrast 4.5″ LCD display, no paper is required. However, you can print [...]
Marine Navigation & Instruments > NMEA Cables & Sensors
J2K100 NMEA 2000® / J1939 Bridge (Engine/Transmission/Genset Gateway) Maretron’s J2K100 attaches directly into J1939 networks of compatible engines, transmissions, and gensets and converts the J1939 engine data to the NMEA 2000® marine digital interface. Critical engine, transmission, and genset data is then distributed throughout the vessel over a single cable where it can be monitored [...]
Marine Navigation & Instruments > NMEA Cables & Sensors
Micro Double-Ended Cordset – 1M Mechanical Contact Carrier Mat/Color: Thermoplastic PUR/Blue-Gray Molded Body Mat/Color: Thermoplastic PUR/Blue-Gray Contact Mat/Plating: Brass/Gold Coupling Nut Mat/Plating: Brass/Nickel Connector Outside Diameter: 0.59″Electrical Current Rating: 4.0 Amps Voltage Rating: 250 VCable Outer Jacket Mat/Color: PVC/Gray Conductor Insulation Material: HDPE (data pair), SRPVC (power pair) Number of Conductors: 4X22 AWG, 22 AWG [...]
Marine Navigation & Instruments > NMEA Cables & Sensors
NMEA Cable, 1 x 7 Pin Connector, 5 MetersReplaces Furuno Part # 000-144-418 WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
Marine Navigation & Instruments > NMEA Cables & Sensors
Micro Inline Termination Resistor The inline terminator is used where the NMEA 2000® network is terminated at a product, for example the top of the mast at a weather instrument or GPS antenna/receiver. The inline terminator plugs directly into the product with the other end connected to the network cable Micro Termination resistors usually terminate [...]
Marine Navigation & Instruments > NMEA Cables & Sensors
Micro Termination Resistors Termination Resistors are required on a NMEA 2000® network and are placed at each end of a network trunk cable. Like the double-ended cordsets, the termination resistors are waterproof and continue to function even while submerged in the bilge. Screw terminal connector for positive connections Termination resistors are used to terminate both [...]
Marine Navigation & Instruments > NMEA Cables & Sensors
NMEA Cable, 1 x 6 Pin Connector, 5 Meters WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
Marine Navigation & Instruments > NMEA Cables & Sensors
SeaTalk 2 / NMEA 2000 Interface Cable (1.5m) Interface cable for connecting E-Series displays to Raymarine SeaTalk 2 or 3rd party NMEA 2000 Devices. Twist-lock connector at the E-series display end, and a standard 5-pin waterproof SeaTalk 2 style connector at the other.