0183 to N2K Gateway with PC Interface, ISO
The NGX-1 is an intelligent gateway that converts NMEA 0183 data to NMEA 2000 (and vice versa), allowing you to share information between devices from the two standards. This creates the possibility of upgrading some of the vessel’s electronics to NMEA 2000 and keeping the remaining NMEA 0183 devices. This can help spread the cost of transitioning to NMEA 2000, reducing the initial upgrade cost to accommodate a new NMEA 2000 device.
The ISO variant connects easily to NMEA 0183 devices with a dedicated pair of data wires for transmit and receive, allowing the NGX-1 to share data bi-directionally if required. OPTOIsolation is included on the input and groundbreaking ISO-DriveTM technology is on the output to keep your devices safe from hazardous ground loops.
The USB Variant allows for quick and easy connectivity to a PC running software that requires NMEA 0183 data.
Thanks to the device being low power, it is powered directly from the NMEA 2000 network, removing the requirement for an independent power supply.
The Actisense NGX-1 also makes it possible to send and receive NMEA 2000 data safely between a PC and an NMEA 2000 network. This creates the possibility of feature-rich software applications replacing or complementing dedicated hardware such as a Multifunction Display (MFD) or Chart Plotter.
Acting as an NMEA 2000 to PC Gateway allows the device to act as a rule-enforcing firewall between the PC and the network, giving the user full control over what data is passed and blocked. The NGX is capable of transferring every currently available NMEA 2000 PGN from the network to a PC application.
Features:
- ISO version has OPTO-isolated input and ISO-Drive output for safely interfacing with NMEA 0183 or RS232 / RS422.
- Advanced configuration using the Actisense Toolkit allows Tx / Rx lists and Tx rates to be set.
- Supports fast-heading at 10Hz.
- Up to 230,400 baud rate data transfer rate.
- Integrated 0.75m ISO cable.
- Diagnostic LEDs on both input and output.
Integrate Seamlessly with Raymarine® Products
The STNG-A06045 adaptor cable enables users to integrate Raymarine SeaTalkNG products into the standard configured NMEA 2000® bus and vice-versa. Currently only available when purchased with an Actisense NMEA 2000® Gateway product.
This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.
| Weight | 0.35 g |
|---|---|
| Dimensions | 6 × 6 × 2 cm |
Brand
Actisense
No accessories available for this product.
Literature
Brochure: Download PDF
No videos available for this product.
Related products
Marine Navigation & Instruments > NMEA Cables & Sensors
USB100 NMEA 2000® / USB Gateway Maretron’s USB100 is a gateway for bridging USB equipment using NMEA 0183 sentences – such as an on-board computer running navigational software – with an NMEA 2000® network. The gateway automatically converts incoming NMEA 2000® messages to NMEA 0183 sentences so you can continue benefiting from navigational and charting [...]
Marine Navigation & Instruments > NMEA Cables & Sensors
Micro Bulkhead Feed-Thru The Bulkhead Feed-Thru allows ease of installation through panels or bulkheads and establishes future connection points in a network installation. The bulkhead feed-thru also maintains the integrity of watertight bulkheads by providing a waterproof seal and connection Features rugged keyways for positive alignment of connections Waterproof rated to IP67
Marine Navigation & Instruments > NMEA Cables & Sensors
NMEA Cable, 1 x 7 Pin Connector, 5 MetersReplaces Furuno Part # 000-144-418 WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
Marine Navigation & Instruments > NMEA Cables & Sensors
RAA100 NMEA 2000®Rudder Angle Adapter The RAA100 is used to adapt commercially available resistive rudder angle senders to the NMEA 2000® network. This allows you to observe rudder angle anywhere on the vessel where there is an NMEA 2000® compatible display such as the Maretron DSM200. The RAA100 is compatible with both the American standard [...]
Marine Navigation & Instruments > NMEA Cables & Sensors
Micro Inline Termination Resistor The inline terminator is used where the NMEA 2000® network is terminated at a product, for example the top of the mast at a weather instrument or GPS antenna/receiver. The inline terminator plugs directly into the product with the other end connected to the network cable Micro Termination resistors usually terminate [...]
Marine Navigation & Instruments > NMEA Cables & Sensors
NMEA Cable, 1 x 6 Pin Connector, 5 Meters WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
Marine Navigation & Instruments > NMEA Cables & Sensors
Furunos NX300 paperless Navtex receiver is the most economical way of monitoring navigational warnings, meteorological warnings, search and rescue information and other data for ships sailing within 200-400 n.m. of shore. Every incoming message is identified and new messages are read from the high-contrast 4.5″ LCD display, no paper is required. However, you can print [...]
Marine Navigation & Instruments > NMEA Cables & Sensors
Micro Tee A Tee is used to tap into the trunk line for adding a drop connection. The standard tee is also available with a cap for a protected diagnostic connection. Tees can be mated with all other devices on the network of the same connector style. Gold contacts for greatest reliability Keyed connectors for [...]