NMEA 0183 Interface Cable
The NMEA 0183 interface provides a bi-directional gateway between an NMEA 2000® network and NMEA 0183 devices.
Ideal for retrofitting NMEA 2000 devices while retaining existing NMEA0183 components, this interface allows boaters a simple way to upgrade to newer technology, sensors, and devices without replacing a whole system. For existing NMEA 2000® networks and systems, this also allows a user to add NMEA 0183 devices to your network, allowing you to choose the products best suited to your boat and sailing.
Simple mounting, connectivity, and a low-profile design allow for easy installation.
Features
- Easy to install
- Allows older products to connect to new, more modern products
- Supports NMEA 0183 Version 4.1
- Filter NMEA 0183 rx/tx sentences and configure transmit frequency via Navico®
- Compatible with Lowrance®, Simrad®, and B & G® MFDs and instrument displays
- NMEA 2000 Compliant
- Standard Micro-C connector
| Weight | 0.4 g |
|---|---|
| Dimensions | 10 × 4 × 3 cm |
Brand
Navico
No accessories available for this product.
No literature available for this product.
No videos available for this product.
Related products
Marine Navigation & Instruments > NMEA Cables & Sensors
Active Coupler with 15 Meter Interconnect Cable. Range: 80kHz to 30mHz WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. This product may not be returned to the original point of purchase. Please [...]
Marine Navigation & Instruments > NMEA Cables & Sensors
Micro Inline Termination Resistor The inline terminator is used where the NMEA 2000® network is terminated at a product, for example the top of the mast at a weather instrument or GPS antenna/receiver. The inline terminator plugs directly into the product with the other end connected to the network cable Micro Termination resistors usually terminate [...]
Marine Navigation & Instruments > NMEA Cables & Sensors
T-Connector For use with red NMEA network
Marine Navigation & Instruments > NMEA Cables & Sensors
TLA100 NMEA 2000®Tank Level Adapter The TLA100 is used to adapt commercially available resistive tank senders to the NMEA 2000® network. This allows you to observe tank levels anywhere on the vessel where there is an NMEA 2000® compatible display such as the Maretron DSM200. The TLA100 is compatible with both the American standard (240-33 [...]
Marine Navigation & Instruments > NMEA Cables & Sensors
Micro Double-Ended Cordset – 0.5M Mechanical Contact Carrier Mat/Color: Thermoplastic PUR/Blue-Gray Molded Body Mat/Color: Thermoplastic PUR/Blue-Gray Contact Mat/Plating: Brass/Gold Coupling Nut Mat/Plating: Brass/Nickel Connector Outside Diameter: 0.59″ Electrical Current Rating: 4.0 Amps Voltage Rating: 250 V Cable Outer Jacket Mat/Color: PVC/Gray Conductor Insulation Material: HDPE (data pair), SRPVC (power pair) Number of Conductors: 4X22 AWG, [...]
Marine Navigation & Instruments > NMEA Cables & Sensors
Fluxgate Cable 10 Meters, 6 Pin Pigtail WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
Marine Navigation & Instruments > NMEA Cables & Sensors
N2KEXT-2RD 2′ NMEA 2000 Cable 2′ NMEA 2000 Cable
Marine Navigation & Instruments > NMEA Cables & Sensors
USB100 NMEA 2000® / USB Gateway Maretron’s USB100 is a gateway for bridging USB equipment using NMEA 0183 sentences – such as an on-board computer running navigational software – with an NMEA 2000® network. The gateway automatically converts incoming NMEA 2000® messages to NMEA 0183 sentences so you can continue benefiting from navigational and charting [...]