Stainless Steel Bottle Opener with Brushed Finish
Corrosion resistant investment cast 316 stainless steel bottle opener wall mounts with two #6 FH fasteners (not included).
WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
| Weight | 0.15 g |
|---|---|
| Dimensions | 6 × 4 × 2 cm |
Brand
Sea-Dog
No accessories available for this product.
No literature available for this product.
No videos available for this product.
Related products
Boat Outfitting > Tools
Footman’s Strap Mount The Footman’s Strap Mount is designed to be bonded with AT-4020 Acrylic Adhesive. This strap mount is 3.25″ long and 1″ wide and holds up to a 1.3″ max strap width. This strap is incredibly strong, paintable, and is rated for over 600 lbs. strength. Use it for battery and tank tie [...]
Boat Outfitting > Tools
Weld Mount 1″ Tall Stainless Stud w/1/4″ x 20 Threads – Qty. 10
1″ Tall Stainless Stud w/1/4″ x 20 Thread Mounts to virtually any surface using the AT-4010 Acrylic Adhesive. This is a structural part with 500 lbs. of tensile strength and 650 lbs. in shear. All studs have 1/4″ x 20 threads. Use for hanging panels, through deck mounts and many other uses.
Boat Outfitting > Tools
Weld Mount 2.5″ Tall Stainless Stud w/1/4″ x 20 Threads – Qty.10
2.5″ Tall Stainless Stud w/1/4″ x 20 Thread Mounts to virtually any surface using the AT-4010 Acrylic Adhesive. This is a structural part with 500 lbs. of tensile strength and 650 lbs. in shear. All studs have 1/4″ x 20 threads. Use for hanging panels, through deck mounts and many other uses.
Boat Outfitting > Tools
Black Nylon Wire Tie Mount The AT-3 tie mount is smaller for panel and other small space applications. This part is molded in black nylon and is sized for a #3 wire tie with a maximum width of .20″. Average pull strength is about 50 lbs. The square base measures .44″ wide. Use this smaller [...]
Boat Outfitting > Tools
White Nylon Wire Tie Mount The AT-5 tie mount is designed to be set into wet resin during the hull lay up or bonded with our acrylic adhesives. It’s designed for a #5 wire tie and has an average pull strength of 150 lbs. It’s approved for submerged bilge applications. Stop putting plywood in your [...]
Boat Outfitting > Tools
Weld Mount 1.25″ Tall Stainless Panel Stud w/0.62″ Base & #8 x 32 Thread – Qty. 15
1.25″ Tall Stainless Stud w/#8 x 32 Thread Our Small Stainless Steel Panel Studs have a wide range of uses. Originally they were used for mounting on the backside of dash panels for mounting to the console. Now they are used for securing a wide range of wire clamps and other small components to composite [...]
Boat Outfitting > Tools
Weld Mount 1.5″ Tall Stainless Panel Stud w/0.62″ Base & #8 x 32 Threads – Qty. 15
1.5″ Tall Stainless Stud w/#8 x 32 Thread Our Small Stainless Steel Panel Studs have a wide range of uses. Originally they were used for mounting on the backside of dash panels for mounting to the console. Now they are used for securing a wide range of wire clamps and other small components to composite [...]
Boat Outfitting > Tools
Weld Mount Manual Dual Pusher Rod f/AT-2010 & AT-4020 – Qty. 10
Dual Pusher Rod The AT-500 dual pusher rod is used to dispense equal amounts of our AT-2010 or AT-4020 adhesive for manual mixing. This dual pusher rod can not be used with our AT-300 or AT-350 mixing tips as it does not generate enough force to push the adhesives through the tip.